Dry Processing of Coal – Progress Report: Tests Conducted on the IMS / Slater Coal Marketing Allair Dry Jig
201613 pages
Test work on a dry jig installed at a Balmoral site, covering coal sized below 50 mm and duff below 12 mm, for producers considering waterless beneficiation.
A 30 tonne per hour pilot Allair dry jig upgraded run of mine coal to thermal coal specification, but could not effectively beneficiate finer duff. Cut point densities and EPM values matched other dry processing equipment, though the jig appeared to give better control of the parameters governing separation. Four tests ran on run of mine coal and two on duff.
Contents
- Introduction4
- Allair jig4
- Tests carried out6
- Results obtained7
- Discussion of results11
How it opens
IMS in cooperation with Slater Coal Marketing installed a 30 tonne per hour Allair dry jig at Slater Coal’s site near Balmoral for the purpose of evaluating the technology and to assess the potential of these jigs to upgrade raw coal to thermal coal specification.
How it concludes
R1500,00
Description
Related Products
Flammability, corrosion resistance and environment by V Mhlawakhe.pdf
Laboratory work turning high ash coal fines into moulded building composites, comparing coal tar pitch against a silicone binder, with strength, burning, corrosion and leaching tests. For product developers.
What this report foundAir blowing converted coal tar into a pitch with 11.27% volatile matter and 87.68% fixed carbon, which bound high ash coal fines into structural composites.
R1500,00
Air blowing converted coal tar into a pitch with 11.27% volatile matter and 87.68% fixed carbon, which bound high ash coal fines into structural composites. Compressive strengths ran from 106.58 to 344.71 MPa and flexural strengths from 48.75 to 159.30 MPa. Flammability was low across all composites and corrosion rates stayed below those of some commercial ceramic tiles.
Underground Trials of Seismic-counter and Goafing Characteristics in Pillar Extraction
2003
Underground trials at South African collieries of a seismic early warning instrument first developed for an Australian longwall, with analysis of how roof layers fail during pillar extraction.
What this report foundA stand-alone device was built that detects micro-seismicity within 100 m of the roof and raises an alarm when preset thresholds are exceeded, giving early...
R1500,00
A stand-alone device was built that detects micro-seismicity within 100 m of the roof and raises an alarm when preset thresholds are exceeded, giving early warning of goafing. Input parameters proved not to vary with geotechnical setting. Man-made noise triggering false alarms remained the main obstacle, addressed by signal conditioning and sensor placement.
Can old bord-and-pillar workings be mapped from surface?
2016
Desktop review updating two earlier assessments, weighing borehole scanning, robots and unmanned aerial platforms as routes to locating old workings ahead of opencast drilling and blasting.
What this report foundNo surface geophysical method can map individual bords and pillars at the depths typical of the Witbank coalfield, a limit the review attributed to physics...
R1500,00
No surface geophysical method can map individual bords and pillars at the depths typical of the Witbank coalfield, a limit the review attributed to physics rather than to technology, since the targets are small relative to their depth and conductive layers often lie above the seam. Borehole laser scanning remains the workable option, with sonar suited to flooded workings.
Multi-client Aeromagnetic Data Merge & Interpretation – Witbank Coalfield
2005
Merged magnetic coverage and dyke interpretation across most Witbank mining and exploration ground, delivered as maps and GIS files for geologists planning around intrusions.
What this report foundGovernment and industry aeromagnetic data over the Witbank Coalfield were merged into one set of maps and GIS compatible files, and roughly 1200 dyke traces...
R1500,00
Government and industry aeromagnetic data over the Witbank Coalfield were merged into one set of maps and GIS compatible files, and roughly 1200 dyke traces were interpreted from them. Purchase of a 200 m line spacing government survey removed the need for infill flying. One participating company valued advance knowledge of a single underground dyke at about R15 million.